Duux DECT baby monitor Specifications download pdf (Page 5)

testing the parent unit

•

First ensure that the baby unit has been set up and is working

correctly following the previous instructions.

• To test the parent unit you must ensure that it is at least 16.5 feet (5

meters) away from the baby unit.

• Turn the sensor pad OFF by means of switch (11).

• Place a sound source such as a radio in the nursery at least 3.5 to 5 feet

(1 to 1.5 meters) away from the baby unit, close the nursery door and

go to another room.

• Set up the parent unit in the docking station.

• Turn on the power (15) and adjust the volume up (16a) or down (16b)

to a comfortable level.

• You will hear sounds from your nursery and some of the sound lights

(A-E) will come on. The louder the sound the more lights will come on.

• Lift the parent unit from the docking station and walk around your

house and garden, ensuring that you can hear the sounds from the baby

unit at all times. The monitor will work up to a distance range of 1000 feet (300meters) approximately.

Depending on the surrounding conditions as well as spatial and structural factors, the range may

be reduced. The range indoors is normally less than outdoors.

• If you lose the signal from the baby unit an alert tone will be emitted from the parent unit every

10 seconds and the LCD will ﬂash until the link is restored. The LCD will show 'No Link'.

If this happens, move closer to the baby unit.

IMPORTANT !

TEST YOUR SENSOR PAD BEFORE PROCEEDING FURTHER:

1 Turn the sensor pad switch to ON at the back of the baby unit (11). The sensor pad LED on the baby unit

will light up if movement is detected.

2 Check the sensor pad is working by touching the crib mattress gently anywhere near where your baby

will be sleeping.

3 Each touch should produce a ﬂash of the green sensor light on the baby unit (H) and on the parent

unit (E) together with an audible tick sound. The volume of the tick can be adjusted.

4 Test the alarm by continuing to touch the mattress for a few moments and then step away from the crib

and stop all movement near the sensor pad.

5 After approximately 20 seconds the alarm will sound and the red alarm light will come on (I) on the

baby unit and (E) on the parent unit.

6 If movement is detected again after the alarm has activated then the red alarm light will ﬂash (I) on the

baby unit and (E) on the parent unit to let you know that the alarm has activated.

7 To reset the alarm, switch the baby unit oﬀ and on again.

setting up your parent unit

Connect the electrical adaptor into a nearby wall socket.

Press and hold (15) for 3 seconds until the LCD/Power LED illuminates.

A link will now be made between the parent unit and baby unit.

WARNING about the danger of cords:

STRANGULATION HAZARD! - Keep cords out of the reach of children.

Do not use with an extension cord.

WARNING! STRANGULATION HAZARD! Children have STRANGLED in

cords. When using without protective covering. Keep this cord out of the reach of

children (more than 3ft (0.9 m) away).

• Check immediately the location of corded monitors to make sure cords are out of arm’s reach of your

baby and other young children.

• Place cords more than a metre away from any part of the crib. The monitor must not be used in any other

sleep environment.

• Check the location of the monitor periodically, as what is within arm’s reach to a baby will change as the

baby grows.

• Make sure the sensor cords are taut and not dangling to reduce the strangulation hazard.

• Do not place furniture or other obstructions on the adaptor cords and be sure to posistion them so that

nobody can trip over them.

• Keep adaptor cords away from hot surfaces such as radiators and central heating pipes.

• Be careful not to posistion the adaptor where a child might try to step on it.

• Never use Tommee Tippee monitor adaptors with any other equipment. Nor should you use any other

adaptors with your Tommee Tippee monitor.

• Please note that the adaptors become warm in use - this is quite normal and not a hazard.

• The adaptors convert your AC power to safe low DC voltage.

• Use the power adaptor provided.

setting up the movement sensor pad

The monitor has the ability to monitor your baby’s movements via the highly sophisticated movement

sensor pad. It is designed for use in a crib with a ﬂat, ﬁrm base. It should not be used in a travel crib, bassinet,

moses basket or a swinging crib.

• Place the sensor pad in the middle of the crib between the crib mattress and the crib base. Place baby at

the bottom of the crib.

• Ensure the sensor pad is positioned the correct way up and that the connecting cord is fed through the

base of the crib out of accessibility range of your baby (50cm from the surface of mattress) and other

young children.

• If the crib has a solid base it may be necessary to make a small hole through which the connecting

cord can pass.

• Ensure the connecting cord plug is pushed fully into the socket underneath the baby unit.

• Do not hang cable over the top or through the bars of the cot.

• Place the cable down and onto the ﬂoor.

1 2 3 4 5 6 7 8 9 10 ... 21 22

algún movimiento 13

Comments to this Manuals

No comments

Duux DECT baby monitor Specifications Page 5

Comments to this Manuals

Related products and manuals for Baby video monitors Duux DECT baby monitor